Answered: The composite bar, firmly attached to…

The composite bar, firmly attached to unyielding supports, is initially stress-free. What maximum axial load P can be applied if the allowable stresses are 10 ksi for aluminum and 18 ksi for steel?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A reinforced concrete collumn 200mm in diameter is designed to carry an axial compressive load of…

A: Answer: The required cross-sectional area of the reinforcing steel is 1650 mm2.

Q: A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138, Detennine…

A: Given The outside diameter of hollow steel tube is D=138 mm. The inside diameter of tube is d=120…

Q: A bar AB of length L and uniform cross section is attached to rigid supports at A and B before being…

A: Let the bar AB have a uniform cross-section of area = A Drawing the FBD of the bar AB:

Q: A mild steel rod of 25 mm diameter and 400 m long is encased centrally inside a hollow copper tube…

A: Axial deflection of arbitrary cross-sectional bar of elastic material having length L is given by…

Q: A constant wind blowing against the side of this chimney has caused creeping strains in the mortar…

A: Let us consider the height of the chimney is h and having constant cross-section against wind, the…

Q: 8. A steel bar of 40mm x 40mm square cross-section is subjected to an axial compressive load of…

A: Answer: The elongation of the bar will be ◆ When 30mm × 30mm square section : 2.22 mm. ◆ When 40mm…

Q: A round steel tension member 40 in. long is subjected to a maximum load of 6,500 lbf. (a) What…

A: Given:- Length : 40 in Load : 6500 lb

Q: A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig. Axail loads are…

Q: Problem No. 2: Compute the increase in stress for each element if the temperature increases by 100°F…

A: As per given question We have to find determine increse the strss of each segment

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

Q: A hollow cylinder of external diameter 50 mm and internal diameter 30 mm is subjected to tensile…

Q: Calculate the normal stress in the copper rod if the temperature of the entire assembly is raised by…

Q: The rigid bar of negligible weight is pinned at o and attached to two vertical rods. Assuming that…

Q: (Q1) A steel tube, 25 mm outside diameter and 12mm inside diameter, cames an axial tensile load of…

Q: A load Pis supported by a structure consisting of rigid bar ABC, two identical solid bronze (E -…

Q: The lap point is fastened with four 20-mm-diameter rivets. the working stresses are 110 MPa for…

Q: Do larger members fail at comparatively lower stresses than smaller members?

A: When a moment or couple is acting over the member, then the size of the member is a matter of…

Q: Assume that the axial load P applied to the lap joint is distributed equally among the three…

A: Answer: The maximum allowable value of load that can be applied on the joint is 37.7 kN.

Q: An axial load of 5000 kN is to be supported by short reinforced concrete column 400 mm x 500 mm with…

A: Given: The axial load, P = 5000 kN The area of the column, Ac = 400 mm x 500 mm The length of the…

Q: c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile…

Q: A wooden beam and a steel plate will be attached with three steel bolts. If the plate will be loaded…

A: Given: The magnitude of force P is P=120 kN. The factor of safety is n=3.25. Determine the force…

Q: Find the safe value of the axial load P in a circular column consists of circular 125mm wooden post…

A: Given data: The working stress for wood, σw=15 MPa. The working stress for concrete, σc=18 MPa. The…

Q: 210. An aluminum tube is fastened between a steel rod and a bronze rod as shown in Fig. P-210. Axial…

Q: 2. An aluminum rod is 1.5 m long. For aluminum, Young's Modulus is E = 70 GPa. An axial force of 3…

Q: Two square bars (15mm thick) are bolted together as shown. Volt's allowable shear stress is 90 MPa,…

Q: An iron column of annular cross-section has an outer diameter of 200 mm and is subjected to a force…

A: Given Data⇒Iron column of annular cross-sectionOuter diameterD=200 mm=0.2 mForceF=75 KN=75×103…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal…

Q: submersible cylinder used in research has a cylindrical pressure hull of outside diameter 3.0 m and…

Q: The 20-mm-diameter bolt fastens two wooden planks together. The nut is tightened until the tensile…

Q: Problem 2.19 Rigid bar ABCD is initially horizontal before the load W is applied and a change of…

Q: A gazebo is planned to be constructed in a community park as an additional shelter for visitors from…

A: Solution: Given Data: A=7200 mm2SR=0.026E=200 GPaσy=233 MPaFOS=1.67K=0.7 (for Fixed-pinned end)

Q: A steel tube, 25 mm outside diameter and 12mm inside diameter, cames an axial tensile load of 40 kN.…

A: GivenD=25 mm=0.025md=12 mm=0.012mF=40 kN=40×103 Nσmax=225 MN/m2=225 ×106 N/mAskedσ=?Fmax=?

Q: For the lap joint below, the maximum safe load P if the bearing stress of the plate is limited to…

Q: Three equidistant vertical rods, each of 20 mm diameter, support a load of 25 kN in the same plane…

A: Given data: As the diameter of each rod is the same, so the cross-section area will be also the…

Q: The homogeneous bar AB weighing 2000 lb. is supported at either end by a steel cable. Calculate the…

Q: QUESTION 3: Square profile made of hollow 1045 steel, with a length of 6 meters with a…

A: Given data: Cross-section of Square hollow profile of steel pipe is drawn below. Cross-sectional…

Q: The circular column is subjected to a compressive force of 5kN if the stress in the column is…

Q: Activity 1: A rectangular piece of wood, 50 mm x 100 mm in cross-section is used as a compression…

A: given:compressive stress σ=20MPadimension of block =50mm×100mm

Q: 4. A load of 25 KN is to be supported by three equidistant vertical rods as shown. At first, all the…

A: To find: The stress in the rods. Given: The young modulus of steel is Esteel=205 GPa and Ecopper=100…

Q: 2- Aluminum tube AB is fixed on support A, and the load P=60 KN is applied on Steel rod BC that is…

A: Write the given data:

Q: The link shown, made of AISI C1045 steel, as rolled, is subjected to a tensile load of 8000 Ib. Let…

A: The material given is AISI C1045 steel. The tensile load is F=8000 lb. The properties of material…

Q: A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig. Axail loads are…

Q: Calculate the internal force (positive if tensile, negative if compresive) in rod (1). Use a FBD…

Q: Aluminum tube AB is fixed on support A, and the load P=60 KN is applied on Steel rod BC that is…

Q: A homogeneous 800 kg bar AB is supported at either end by a cable. Calculate the smallest area of…

A: Given:m=800 kgσb=90 MPaσs=120 MPa

Q: A load of 25 KN is to be supported by three equidistant vertical rods as shown. At first, all the…

A: Given details Es=205GPa Ec=100GPa diameter of rod = 20mm Total load applied of system = 25+20=45 KN

Q: An axial bar fixed at both ends with no loads applied is subjected to an increase of temperature.…

Q: 105. For the truss shown in Fig. P-105, determine the cross-sec- tional areas of bars BE, BF, and CF…

Concept explainers

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.

Question

Steel
Aluminum
A = 1.25 in.2
E = 10 x 10° psi
A = 2.0 in.2
E = 29 x 10° psi
P
15 in-
-12 in.-

The composite bar, firmly attached to unyielding supports, is initially stress-free. What maximum axial load P can
be applied if the allowable stresses are 10 ksi for aluminum and 18 ksi for steel?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2 A hollow short cast iron column has outside and inside diameters of 250 mm and 150 mm respectively. The column is subjected to an axial load applied at a distance of 60 mm from the center of the section. (a) Calculate the maximum safe load if the allowable stresses are 110 MPa compressive and 30 MPa tensile, calculate also the position of the NA.
Find the safe value of the axial load P in a circular column consists of circular 125mm wooden post and a 200mm x 200mm concrete footing separated by a steel plate. The working stresses are 15 MPa for wood and 18 MPa for concrete.
A mild steel rod of 25 mm diameter and 400 m long is encased centrally inside a hollow coppertube of external diameter 35 mm and inside diameter 30 mm. The ends of the rod and tube arerigidly attached, and the composite bar is subjected to an axial pull of 40 kN. If E for steel andcooper is 200 GN/m2 and 100 GN/m2 respectively, find the stress developed in the rod and thetube. Find also the extension of the rod.
A hydraulic press exerts a total load of 5.5 MN. This load is carried by two steel rodssupporting the upper head of the press. If the safe stress is 95 MPa and Young Modulus of209 KN/mm?. Find; (i) Diameter of the rods (ii) Extension in each rod in a length 3.5 m
The member consists of the steel rod AB that is screwed into the end of the bronze rod Find the largest value of P that meets the following design criteria: (a) the overall length of the member is not to change by more than 3 mm; and (b) the stresses are not to exceed 140 MPa in steel and 120 MPa in bronze. The moduli of elasticity are 200 GPa for steel and 80 GPa for bronze.
The anchor opposite is made of Cr-Ni steel. Thereelastic limit is 520 Mpa. What should be the minimum diameter inanchor shear if the load F is 50kN? Consider a safety factor of 2.Please note that the safety factor is applied tothe elastic limit.
A compressive load of 219 kN is resisted by a rectangular strut which has one side measuring 83 mm. If the stress in the strut is 164 909 kPa, what is the length of the other side of the strut?
3 m Load D 2 m+ 3 m The member AC is made from an aluminium alloy and has a rectangular cross section of 100mm x 10mm. Calculate the stress in member AC if a load of 57.4 kN is applied at point D.
Assume that the axial load P applied to the lap joint is distributed equally among the three 20-mm-diameter rivets. What is the maximum load P that can be applied if the allowable stresses are 40 MPa for shear in rivets, 90 MPa for bearing between a plate and a rivet, and 120 MPa for tension in the plates?
(4) The plunger of an oil pump is held against the operating cam by a spring made of No.10 W&M gage steel wire coiled with an outside diameter of 7%-in. There are five active coils. The open length is 1.1875in. What are the length & stress when a load of 30lb is applied.
I Reviev Part A If the allowable tensile stress for the bar is (0t)allow = 22.6 ksi, and the allowable shear stress for the pin is Tallow = 12.2 ksi. Assume the hole in the bar has the same diameter d as the pin. Take t = 1/4 in. and w = 2 in. (Figure 1) Determine the diameter of the pin so that the load P will be a maximum. Express your answer to three significant figures and include appropriate units. HÀ ? d = Value Units Submit Request Answer Part B What is this maximum value for P? Express your answer to three significant figures and include appropriate units. Figure 1 of 1 HA ? w/2 P = Value Units w/2 Submit Request Answer
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Draw appropriate FBDs showing how the internal forces were determined. A square bar (side length = 50 mm) is welded to a fixed supporting slab. A 30-mm diameter pin is inserted in the bar. When the loading shown is applied, determine the following: a. maximum normal stress in the bar (MPa) and bearing stress between the pin and the bar (MPa)b. stress in the weld between the bar and the supporting slab (MPa)c. shear stress in the pin (MPa) and shear stress in the bar (MPa)