The figureshows a copper rod that is placed in an aluminum tube. The rod is 0.005 in. Ionger than the tube of length L = 10.52 in. Find the maximum safe load P (in Ib with four decimal places) that can be applied to the bearing plate, using the following data: area of copper = 2.64 sq, in. area of aluminum = 3.04 sq, in. E of copper = 17022171 ksi E of aluminum = 10073078 ksi allowable stress for copper = 19926 ksi allowable stress for aluminum = 10407 ksi Bearing plate ... 0.005 in. Copper ·Aluminum

The figureshows a copper rod that is placed in an aluminum tube. The rod is 0.005 in. Ionger than the tube of length L = 10.52 in. Find the maximum safe load P (in Ib with four decimal places) that can be applied to the bearing plate, using the following data: area of copper = 2.64 sq, in. area of aluminum = 3.04 sq, in. E of copper = 17022171 ksi E of aluminum = 10073078 ksi allowable stress for copper = 19926 ksi allowable stress for aluminum = 10407 ksi Bearing plate ... 0.005 in. Copper ·Aluminum

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.7.10P: Three round, copper alloy bars having the same length L but different shapes are shown, in the...

See similar textbooks

Similar questions

The figureshows a copper rod that is placed in an aluminum tube. The rod is 0.005 in. longer than the tube of length L = 10.14 in. Find the maximum safe load P (in lb with four decimal places) that can be applied to the bearing plate, using the following data: area of copper = 2.78 sq, in. area of aluminum = 3.28 sq, in. E of copper = 17013025 ksi E of aluminum = 10072240 ksi allowable stress for copper = 19000 ksi allowable stress for aluminum = 10802 ksi
Figure 5 displays a copper rod that is placed in an aluminum tube. The rod is 0.005 in. longer than the sleeve. Find the safe load (P) that can be applied to the bearing plate. Identify the safe load in kips. Bearing plate СОРРER ALUMINUM Area (in?) Е (psi) 3 17 x 106 10 x 106 0.005 in. Allowable Stress (ksi) 20 10 10 in. Copper - Aluminum Figure 5
A bar, 12 mm in diameter is acted upon by an axial load of 20 kN. The change in diameter is measured as 0.03 mm. DeterminePoisson’s ratioYoung’s modulusBulk modulus Assume modulus of rigidity as 80 GPa
E. Rigid bar AD is horizontal before the weight of 112 lb is applied to the end of wire BC at C. The wires have a radius of 0.025" and are made of A913 steel. Determine the rotation of AD and how far C will move down due to application of the weight See Appendix of text for any material properties needed. Ans: 0.00071 radians 3 ft - 2 ft -3 ft- D B 4 ft W
Figure 5 displays a copper rod that is placed in an aluminum tube. The rod is 0.005 in. longer than the sleeve. Referring to the maximum allowable stress in aluminum, find the safe load P in kips that can be applied to the bearing plate. Bearing plate СОРРER ALUMINUM Area (in?) E (psi) 3 17 x 106 10 x 106 0.005 in. Allowable Stress (ksi) 20 10 10 in. Copper -Aluminum Figure 5
Question 1 A tensile load of 40 kN is acting on a rod of diameter 40 mm and of length 4 m. A bore of diameter 20 mm is made centrally on the rod. To what length the rod should be bored so that the total extension will increase 30% under the same tensile load. Take E = 2 x 10$ N/mm2.
A round steel bar with a diameter of 1.500 in is subjected to the axial loads shown. P1 = 95 k, P2 = 115 k, P3= 55 k, P4 = (P1-P2+P3) k. If Section 2 has a length, L2 = 65 inches, find the change in length of Section 2. Report the answer below in inches, absolute value, 3 significant digits. P1 Your Answer: 100 inches Round Steel Bar P2 Section 2 12 P3 80 inches P4
Question 5 A lead of 5kN is to be raised using a steel wire. Find the minimum diameter of the wire required to raise the load if the yield stress of steel is 300MP.. 5kN
A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load of 500 MN. If the maximum allowable stress for this hollow rod is 325 kN/mm?, calculate the minimum thickness of the rod. Give your answer in millimetres (mm) and to 2 decimal places.
1. You are to design an axially loaded member that is to carry a load of 5,000 lb. The member is to be made of ASTM A36 steel and have a total length of 24 in. Due to the design requirements the maximum allowable elongation of this member under the stated load is 0.025 in. Find the smallest allowable diameter of the member. a. Given: PL where ô is member elongation, P is axial load, L is initial member length, E is the material's Modulus of Elasticity, EA and A is the member's cross section area E136 = 29*10° psi (Beer, 746)
A 1∕2-in.-diameter round steel rod 40 ft long supports a loadof 4 kips. How much will it elongate? e= ΔL /L f = P/A E = (P∕A)/ (ΔL∕L) = (PL) / (A(ΔL))
find the tensile of the bolt with diameter 38mm,80kN