The stop-start system in a car turns the motor off when the car is stopped and on when the car starts to move. For the restart, engineers add a capacitor that is charged using energy generated as the car brakes. If the motor is modeled as a simple resistance with a switch in series with the capacitor, the car is to be started within a time t, the current needed to make the motor start is lo, and given a potential Vo, which of the following expressions describes the electric charge Q in the circuit as a function of time? -tI. Q (t) = CVoe vo Q (t) = Ye-Rc Q (t) = Co te-RC Low partial credit Q (t) = CVot CORRECT High partial credit %3D T M Crawford

The stop-start system in a car turns the motor off when the car is stopped and on when the car starts to move. For the restart, engineers add a capacitor that is charged using energy generated as the car brakes. If the motor is modeled as a simple resistance with a switch in series with the capacitor, the car is to be started within a time t, the current needed to make the motor start is lo, and given a potential Vo, which of the following expressions describes the electric charge Q in the circuit as a function of time? -tI. Q (t) = CVoe vo Q (t) = Ye-Rc Q (t) = Co te-RC Low partial credit Q (t) = CVot CORRECT High partial credit %3D T M Crawford

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The arc length voltage characteristic of a DC arc is given by the equation V=24+4L where 'V' is the arc voltage in volts and L' is the length in mm. The static volt-ampere characteristic of the power source is approximated by a straight line with no load voltage of 80V and the short circuit current of 600A. Then the optimum arc length is (mm).
Suppose you want the current through a 1.85 H inductor in series with a 0.45 \Omega resistor to be reduced to 0.100% of its initial value. In how much time, in seconds, will this occur after you throw the switch?
Find the Net impulse
Time constant of thermocouple is 5 milliseconds. An engineer measures the temperature of water and sees that the temperature is less than the real temperature of the boiling water (100 C). How long does the engineer need to wait at least to see the 98 C? none of the above 20 milliseconds 10 milliseconds 15 milliseconds not sufficient information 17 milliseconds
The input power to a 3-phase load is measured as 8kW. If the line voltage and power factor of the load are 426 V and 0.8, then the value of line current is
What is internal impulses?
Identify the degree of freedom of the following system Select one: O2 0 4 03 늘 + 2m F,(1) 늘
B: A motor drives a hoist which raises a load of 1000 kg with a velocity of 1 m/sec, calculate the input power of the motor assuming the hoist gearing efficiency to be 0.8, motor efficiency to be 0.75.
nalysis this circuits, every details others answers. thank you
Q3:A: (a) A 10-hp 230-volt shunt-wound motor has rated speed of 1000 rpm and full-load efficiency of 86 percent. Armature-circuit resistance, 0.26 ohm; field-circuit resistance, 225-ohms. If this motor is operating under rated load and the field flux is very quickly reduced to 50 percent of its normal value, what will be the effect upon back emf, armature current and torque? What effect will this change have upon the operation of the motor, and what will be its speed when stable operating conditions have been regained?
Change the 10kN to 12kN for it to be stable
Give one application of Electric Drives in the industry (ex. drives the fans of coolers in a gas plant). Create simple engineering drawing or diagram (ex. 2D, 3D, isometric, PFD, P&ID, etc.) for your chosen application.