Two flywheels are pinned to opposite ends of a metal bar. The smaller flywheel has a mass of 40 kg and a radius of 0.25 m. The larger flywheel has a mass of 275 kg and a radius of 1.75 m. The bar has a mass of 2 kg and a length of 3 m. A wooden plate acts as a ripcord by temporarily pressing it against the flywheels and rapidly translating it to the left at v = angular velocity of 25 rad/s and the large flywheel has an angular velocity of 3.5714285714286 rad/s. The flywheel-bar assembly is then set on frictionless ice such that the axes of rotation are perpendicular to the ice surface. 6.25 m/s. The plate is removed when the small flywheel has an 0.05, which eventually causes the flywheels to stop spinning relative The flywheel pins have Hk = to the metal bar. Angular momentum is conserved, so the whole assembly continues spinning as a rigid body about the center of mass. What is the final angular velocity of the assembly? rad/s. The flywheels and bar rotate about their combined center of mass at w- Round answer to 3 significant figures.

Two flywheels are pinned to opposite ends of a metal bar. The smaller flywheel has a mass of 40 kg and a radius of 0.25 m. The larger flywheel has a mass of 275 kg and a radius of 1.75 m. The bar has a mass of 2 kg and a length of 3 m. A wooden plate acts as a ripcord by temporarily pressing it against the flywheels and rapidly translating it to the left at v = angular velocity of 25 rad/s and the large flywheel has an angular velocity of 3.5714285714286 rad/s. The flywheel-bar assembly is then set on frictionless ice such that the axes of rotation are perpendicular to the ice surface. 6.25 m/s. The plate is removed when the small flywheel has an 0.05, which eventually causes the flywheels to stop spinning relative The flywheel pins have Hk = to the metal bar. Angular momentum is conserved, so the whole assembly continues spinning as a rigid body about the center of mass. What is the final angular velocity of the assembly? rad/s. The flywheels and bar rotate about their combined center of mass at w- Round answer to 3 significant figures.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.75P

See similar textbooks

Similar questions

The strings AB and AC connect 500-g mass A to the vertical shaft BC. When the shaft rotates with a constant angular velocity of 15 rad/s, the ball has circular motion in the horizontal plane with the strings having angles of a = 55° shown in the figure. Find the tension forces at the strings AB and AC. B 500g 400 mm 400 mm
The strings AB and AC connect 500-g mass A to the vertical shaft BC. When the shaft rotates with a constant angular velocity of 15 rad/s, the ball has circular motion in the horizontal plane with the strings having angles of a = 55° shown in the figure. Find the tension forces at the strings AB and AC. 500g A uui 00t 00 mm
The wheel shown in the figure has the inner and outer radius of r1= 0.125 m and r2= 0.575m, respectively. Assume the two ropes shown are firmly attached to the inner radius r1. L₁ F G B r. E D a) If the upper wire of the wheel has a velocity v=5.6 m/s, the instantaneous centre of zero velocity is located at (A or B or D or G or F) b) Determine the angular velocity of the wheel w= = rad/s c) Determine the velocity of point E (be careful of signs) VE=----i_ + ---- J
For the circular thin plate with a square hole as shown in the image below, its radius R = 0.48 m and the side of the square /= 0.21 m, and the material has a mass per unit area of 12 kg/m2. If at the instant shown, it is subjected to a force P = 38 N, and has a counterclockwise angular velocity of W = 2.6 rad/s, determine magnitude of the support reaction at point O at this instant. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper unit. Take g = 9.81 m/s?. R P
Q-4) The rod, having a weight of 16N and a length of 2.5m, contains a joint at O which is 0.5m distant from point B. The other end of the rod is attached to a 2,5 m- 0,5 m spring that is compressed by 4cm A with Ks= 250N/cm. At this moment the rod is horizontal. When released; calculate it's angular velocity (passing by the vertical position) and reaction forces at the joint 0.
For the circular thin plate with a square hole as shown in the image below, its radius R = 0.32 m and the side of the square /= 0.18 m, and the material has a mass per unit area of 12 kg/m². If at the instant shown, it is subjected to a force P = 30 N, and has a counterclockwise angular velocity of W = 4.2 rad/s, determine magnitude of the support reaction at point O at this instant. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper unit. Take g = 9.81 m/s². R @ Your Answer: Answer units P
1. The slotted link is pinned at 0, and as a result of the constant angular velocity é = 6 rad's it drives the peg P for a short distance along the spiral guide r = (0.6 0) m where e is in radians. When e = 80 deg, Find: a. Find e, é, ë,r,r, ř. (in radians) b. The radial components, transverse components, and magnitudes of the velocity [4maeie). - The radial components, transverse components, and magnitudes of the acceleration of P at the instant. asks). %3D 0.8 m r=0.6 0 ô =6 rad/s
Three bodies are fixed on a shaft rotating at 500 rpm. The mass of the bodies are 3.5 kg, 2.5 kg and 2 kg. The radii of rotation can be taken as 60 cm, 40 cm and 25 cm. If a balancing body of 1.5 kg is to be placed, then find the unbalance in the system. The first body can be assumed to be at 45° from positive x axis, second body is at 90° from first body and third body is at 180° from positive x-axis. All the angles are measured in anti-clockwise direction.
The figure shows a rotor with three unbalances on it. To the L and R balancing planes given in the figure, to fully balance this rotor. Balancing masses will be placed at a distance of r=40 cm from the rotation axis. Calculate these masses and the angular positions at which they should be placed.
A ring of mass m =1 kg and radius R = 1m is attached to a vertical shaft by means of a frictionless pin. Coordinates xyz are fixed to the ring as shown and the frictionless pin at A is aligned with the x-axis. The vertical shaft precesses about the Z-axis with constant angular velocity 2 = 1 rad/s. (a) At a particular moment when 0 = 30° and = 4 rad/s, find the value of Ö . This comes from a sum of the moments about the x-axis. Do not neglect gravity. (b) Find the torque or moment necessary that must be applied about the vertical shaft in order to keep it turning at a constant rate of N = 1 rad/s. Ring R XG A 1 Ixx = lyy =mR? G Iz = mR?
A torque T = 0.30 N-m is applied to a bevel gear B. Bevel gear D meshes with gear B and drives pump A. Gear B has a radius of gyration of 150 mm and a weight of 50 N, whereas gear D and the im- peller of pump A have a combined radius of gy- ration of 50 mm and a weight of 100 N. Find how many revolutions of gear B are needed to get the pump up to 200 rpm from rest. What is the power output of the pump at this speed if it is 90% efficient.
The operation of the fuel pump for an automobile depends on the reciprocating action of the rocker arm ABC, which is pinned at B and is spring loaded at A and D. The smooth cam C is in the position shown. The vertical force acting on the rocker arm at A is F₁60 N, and at C it is Fo 155 N (Eigure 1) Figure 50 mm Figure 10 mm 50 mm The operation of the fuel pump for an automobile depends on the reciprocating action of the rocker arm ABC, which is pinned at B and is spring loaded at A and D. The smooth cam C is in the position shown. The vertical force acting on the rocker arm at A is F =60 N. and at C it is Fe=155 N. (Figure 1) 20 mm- 10 mm 1 of 1 mm. 1 of 1 Part A Z Determine the and y components of the reaction force on the rocker arm ABC at the pin for equilib Express your answers using three significant figures separated by a comma. 195] ΑΣΦ | 11 | voc | B₁, B,= Submit Part B Part B Fo Submit Request Answer Determine the magnitude of the force along the spring DF for equilibrium.…