Two solid cylindrical rods support a load of P = 39 kN, as shown. Rod (1) has a diameter of 16 mm and the diameter of rod (2) is 11 mm. Determine the axial stress in rod 2. Assume a = 2.2 m, b = 4.6 m, c = 2.7 m, and d = 2.4 m. Use positive for tensile stress and negative for compressive stress. Express your answer in MPa rounded to the nearest whole number. Two solid cylindrical rods support a load of P = 39 kN, as shown. Rod (1) has a diameter of 16 mm and the diameter of rod (2)is 11 mm. Determine the axial stress in rod 2. Assume a = 2.2 m, b = 4.6 m, c = 2.7 m, and d = 2.4 m. Use positive for tensile stressand negative for compressive stress. Express your answer in MPa rounded to the nearest whole number.a...(1)b(2)dBP

Answered: Image /qna-images/answer/38f32046-ab78-4c4d-b3e5-89eedb6cfbb6.jpg

Engineering

Mechanical Engineering

Two solid cylindrical rods support a load of P = 39 kN, as shown. Rod (1) has a diameter of 16 mm and the diameter of rod (2) is 11 mm. Determine the axial stress in rod 2. Assume a = 2.2 m, b = 4.6 m, c = 2.7 m, and d = 2.4 m.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.1P: A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the...

See similar textbooks

Related questions

Q: at what distance into the pipe is the

Q: V a A В a

A: a=2.3inb=3.6ind=10.8int=0.4inV=39kips To-Find:- The shear flow through the welded surface at B

Q: R1 = 5 cm. F1 = 1000 N, and R2 = 40 cm. Express the answer in Newtons.

Q: For the simply supported beam carrying the concentrated load P = 268 N at its midspan, determine the…

A: Use simply support beam concept to solve this problem, Given information Total length of…

Q: + 290 Cs +41850000 t ISO,000c +aasooodc00 Ys 10,000s" Find the damping value of where zeta= 0707

Q: Q2) The figure shows a cantilever consisting of steel channel size 127 mm×64 mm. Using…

A: Given:

Q: a supply tank having 14m long and 1.7m diameter is used to store fuel oil with 34degree API at…

Q: A door is constructed of a thin homogeneous slab of material; it has a width of 1 m. If the door is…

Q: e characteristic polynomial method. 6 2

Q: Four forces F1, F2, F3 and F4 are being applied on a plate as shown in Figure 1. If your roll number…

Q: Consider the woman doing push-ups in the figure. She has a mass of 51.3 kg, CG and the distance from…

A: Given data as per the question Mass of the body = 51.3 kg Distance from feet to CG of body =0.85m…

Q: The process shown on the p-v graph below is called

A: Given: To identify the process shown in above plot.

Q: Boat A moves with a constant velocity of 20ft/s, starting from the position shown in the…

A: Given that, Velocity of the boat, VA=20 ft/sec,Velocity of projectile, Vo=96.6 ft/sec,

Q: 2 m 8 m 3 m 4 m - 6 m

Q: Why might a 50 division vernier caliper not be more advantageous, in terms of measurement accuracy,…

A: Vernier caliper is an instrument that is used to measure the dimensions such as the external…

Q: 4Describe in your own words how an aspirator won

A: An aspirator is simple type ejector jet pump. It's objective to produces vaccum with help of venturi…

Q: 4. A symmetric body moves without the influence of forces or torques. Let x, be the symmetric axis…

A: L1=0=I1ω1L2=Lsinθ=I1ω2=I1ωsinαL2=Lcosθ=I3ω3=I3ωcosαtanθ=L2L3=I1I3tanα ............... 1 We know,…

Q: between the uniform 50-kg spool and the wall so that the F8-6. Determine the minimum coefficient of…

Q: Determine the reactions at the Smooth contact points A,B and C 250 N 30 30 0.15 m 0.2 m

A: Apply Static equilibrium to solve this problem

Q: Methane gas has its reduced pressure of 5 and its compressibility factor is 0.8. Compute its…

A: Methane gas has a reduction pressure of 5 and a compressibility factor of 0.8, as we know.by using…

Q: Part (a) Choose the correct free-body diagram for the door. F, Mg Mg F. F. F Mg F Mg F Part (b)…

A: Given data Mass of the door = M = 33 kg Height of the door = h = 2.2 m [ Note : According to…

Q: 2KN Im ア sm Find the displce ment at Poin B mm

Q: A long, 20-cm diameter pipe is carrying hot water. The temperature of the air around the pipe is…

A: Given dataDiameter of pipe = 20 cm = 0.2 mTemperature of air around the pipe = T∞ = 10°CTemperature…

Q: A thin membrane divides a rigid vessel into two equal volumes. The left side initially contains 1.5…

Q: 7.5 The rotor of a stream turbine is a solid disc of uni- form strength and is 20 cm diameter at the…

A: Diameter, d1= 20 cm= 0.2 m. Hence, it's radius, r1= d12= 0.22= 0.1 m Thickness, t1= 2.5 cm= 0.025 m…

Q: 3. Locate the centroid (x, y, z) of the wire which is bent in the shape shown. 2 in. 2 in. 4 in.

A: Given: To find x,y,z

Q: Create a flowchart or process diagram of compression molding machine

Q: 9 Determine the specific speed of the following centrifugal pumps: single

A: Need to find specific speed

Q: Determine the coefficient of performance for a Carnot Cycle Refrigerating Machine and for a Carnot –…

A: Condenser temperature, TH= 86 F= (86-32)59+ 273.15= 303.15 K To find: i) Coefficient of…

Q: The bottom of a 50mm diameter, 2mm thick metallic induction heater is 120C while its thermal…

Q: (a) Kinematic and Kinetic are a branch of the physical sciences. Define what is kinematics and…

A: Kinematics is the study of the motion of points, objects, and groups of objects without…

Q: V4- 15 m/s 30° B 1.5 m Xc 18 m Figure Q2

Q: 9. A solid metal sphere at temperature To is placed in oil kept at temperature T, 0, and u(r,0) =…

A: Assuming that the material is homogeneous and isentropic, the warm conductivity of the material…

Q: 2) Calculate the minimum wall thickness for a cylindrical vessel that is to carry a gas at a…

A: Apply the thin cylinder concept, To proceed the problem.

Q: 1. Determine the distance x to the center of mass of the homogeneous rod bent into the shape shown.…

Q: Draw the shear and moment diagrams for the beam

A: Need to draw Shear and moment diagram

Q: Q6/ A car moving on a rough inclined plane are having the following data: Angle of inclination of…

Q: 2.95 Is the symmetrically loaded barge shown in Fig. P2.95 stable? The center of gravity of the…

Q: Q/draw the projections

A: According to the details provided in the question, we need to calculate THREE PROJECTION VIEW.

Q: • Mechanically speaking, an oar is a beam, loaded in bending. • It must be strong enough to carry…

A: Given data Weight hung =W = 10 x 9.81 NDistance from Collar to point of maximum deflection = 2.05…

Q: superheated steam enters the turbine at 873K and 18MPA. Find the isentropio Also find T2 and turbine…

A: INTRODUCTION : One of the steady flow energy devices is the turbine. The rates of mass and energy…

Q: The 20-kg package has a speed of 1.5 m/s when it is delivered to the smooth ramp. After sliding down…

Q: 1- Extrude faces in AutoCAD 3D modelling? 2- Draw a cylinder in AutoCAD 3D modelling? 3-Hide or…

A: Given Extrude face Cylinder drawing View cube To find AutoCAD modelling steps

Q: The system shown below is to be designed for the gathering of gas. Well "A" is a following gas that…

A: Let take the discharge through a=Q1Let take the discharge through b=Q2Let take the discharge through…

Q: able 11.3. The engineering constants in Example 11.1 E, (GPa) E2 (GPa) G12 (GPa) V12 Nominal (v =…

A: Given dataVf=0.6Vm=0.4E1=148GPaE2=9.65GPaG12=4.55V12=0.3we know thatE1=VfEf+VmEm148=0.6Ef+0.4Em…

Q: Questions 1. Steam from the turbine exhausts directly into the (shell/water) of the condenser. 2. As…

A: Steam in the turbine does work and when steam exhausts from condenser it is converted to low temp…

Q: Design a cast iron trunk type piston for a single acting four stroke engine developing 75 kV…

Q: 5.10 Gas turbine exhaust of Ex. 5.1 is employed in a waste heat recovery boiler to raise steam at p=…

A: To find: The kinetic energy of the system at an arbitrary instant in terms of the indicated…

Q: A rope is wrapped around a circular pulley such that its acceleration is given by a = 10t (in m/s2,…

A: Given:a=10 t m/s2r=0.5 m

Q: eeds to prepare the soup before the end of his shift. Initially, as Tolits is preparing the soup,…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

100%

Two solid cylindrical rods support a load of P = 39 kN, as shown. Rod (1) has a diameter of 16 mm and the diameter of rod (2) is 11 mm. Determine the axial stress in rod 2. Assume a = 2.2 m, b = 4.6 m, c = 2.7 m, and d = 2.4 m. Use positive for tensile stress and negative for compressive stress. Express your answer in MPa rounded to the nearest whole number.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
Solve the preceding problem for an element in plane stress on the bottom surface of a fuel tanker (figure part a); stresses are sx= 105 MPa, sy. = 75 MPa, and ??xy= 25 MPa. Determine the stresses acting on an element oriented at an angle ?? = 40° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle ??.
A simply supported beam is subjected to point load P at mid-span. The normal stress on an element at mid-span is known to be ??x= 1.5 ksi. Determine the element stresses lilt is rotated through angle ? = 450• Show these stresses on a sketch of an element oriented at that angle.
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
A specimen used in a coupon test is shown in the figure. The stresses on element A are known to be sy= -1500 psi. Use Mohr’s circle to: (a) Find the stresses acting on the element oriented at an angle ?? = -35°. (b) Find maximum normal and shear stresses and show them on sketches of properly oriented elements.
A single steel strut AB with a diameter (a) Find the strut force Fs and average normal stress ds= 8 mm supports the vehicle engine hood of a in the strut. mass 20 kg that pivots about hinges at C and D (see (b) Find the average shear stress t aver in the bolt at A,figure parts a and b). The strut is bent into a loop at (C) Find the average bearing stress bon the bolt at A. its end and then attached to a bolt at A with a diameter db= 10 mm. Strut AB lies in a vertical plane.
Two solid cylindrical rods support a load of P = 39 kN, as shown. Rod (1) has a diameter of 16 mm and the diameter of rod (2) is 11 mm. Determine the axial stress in rod 1 and rod 2. Assume a = 2.2 m, b = 4.6 m, c = 2.7 m, and d = 2.4 m. Use positive for tensile stress and negative for compressive stress. Express your answer in MPa rounded to the nearest whole number.
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. The diameter of rod (1) is d1 = 1.66 in. and the diameter of rod (2) is d2 = 2.68 in. Determine the normal stresses in rods (1) and (2). Assume P = 17 kips and Q = 29 kips. Use positive for tensile stress and negative for compressive stress.
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Take d₁ = 30 mm, d2 = 50 mm, and P = 50 kN. P 0.9 m 125 kN 125 KN B 1.2 m Find the average normal stress at the midsection of rod BC. (Input the answer with the appropriate sign.) The average normal stress at the midsection of rod BC is MPa.
Two vertical steel rods support the rigid bar as shown. Initially, the rods are stress-free. Given the data below, determine the stress of rods A and B after the 20 kN load is applied. Neglect the weight of the bar and use E = 200 GPa for steel. L= 3 m D = 3.5 mm A. Stress of rod A (MPa) B B. Stress of rod B (MPa) C. At what temperature AT change would the stresses for both rods be equal? Use a = 11.7 L= 4 m x 10-6 mm/mmC° (C°) D = 5 mm 4m 2m 2m 20 kN