Two uniform, solid spheres (one has a mass M1= 0.3 kg and a radius R1= 1.4 m and the other has a mass M2 = 2M1 kg and a radius R2= 2R1) are connected by a thin, massless rod of length L= 4R1. Find the moment of inertia (in kg.m2) about the axis through the center of sphere 1. (Igphere =MR?). Axis of rotation R, R2

Two uniform, solid spheres (one has a mass M1= 0.3 kg and a radius R1= 1.4 m and the other has a mass M2 = 2M1 kg and a radius R2= 2R1) are connected by a thin, massless rod of length L= 4R1. Find the moment of inertia (in kg.m2) about the axis through the center of sphere 1. (Igphere =MR?). Axis of rotation R, R2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider an L-shaped plate shown in the figure below. Calculate the moment of inertia I (in kg.m2). The mass of the plate is 3 kg, and the width is w = 0.8 m, height h = 0.5 m, and b = 0.2 m. y. W b
P L d R kg A square made of aluminum (density p = 2700 m and has dimension L = 5.20 m and thickness e = 0.80 m. We remove a cylinder of radius R = 0.70 m and at a distance d = 1.30 m from the center of the plate and at 30 deg with the horizontal. Find the centre of mass in x and y of this shape from the lower left corner. Note the centre of mass about for the z-axis is neglected in the answer, since it is obviously at e/2. Xem Share With Class
Two balls of mass ma and m, are connected by a massless rod of length L. The two vertical dashed lines in the figure, below, represent two different axes of rotation (axes a and b). These axes are parallel to each other and perpendicular to the rod. If the ratio between the two moments of inertia, as measured relative to each axis, is 4 = 3. Ib a. Find the ratio of the masses (ma/mp). b. Find the distance from ball a to the system's center of mass. Axis a Axis b L- ma Two balls connected by a massless rod of length L rotate around the two axes shown.
Find the center of mass of the structure about point A of the figure below. Assume a uniform thickness of 15 cm, and a uniform density of 4.0 g/cm³. sphere, radius = 10 cm 58 cm 3 cm XCM = ++ 28 cm ♦ A A -58 cm- 1 72 cm 10 cm 14 cm T YCM = width .5 cm
The figure below shows the positions of the Centers of mass of the three disks on a rotating shaft. m. =6 kg, M2=4 kg, m3=5 kg, r-=100 mm, r2=200 ver3 = 300. B to dynamically balance the shaft it is desirable to place balancing masses of 3 kg each in their planes. Balancing find the positions of the center of mass (004) of mass A in the unit of cm and degrees. The D value in the figure is 200 mm. mlg my m1 37 53 200 mm 150mm 200 mm ma Please choose one n
Find the equivalent moment of inertia of the rocker arm assembly with respect to the location of kt. mass1=10kg Jo=20kg-m2 mass2=15kg, a is half of b. The rocker is 30 centimeters long. (kg-m2) * k1 Jo- k2 m2
It is common to hang objects on doorknobs and over-the-door hooks. There is a limit to the amount of weight that a door can hold because of the forces exerted on the hinges. A door of height h = 2.5 m and width h/2 has a mass of M = 36 kg. The mass is distributed uniformly, so the center of mass is located at the geometric center of the door. One hinge is located a distance h/4 from the top of the door. The second hinge is a distance h/4 from the bottom of the door. Refer to (a) in the figure. The door’s weight is supported entirely by the two hinges and each hinge supports half of the weight. In other words, the vertical force exerted by each hinge is exactly one half of the total weight, including any additional load. For this problem, take the positive y-direction to be directly upward and the positive x-direction pointing from the hinge side of the door to the knob side. 1.) calculate the force, with its sign in Newtons that the upper hinge exerts on the door in the x axis.…
Consider a hollow drainage concrete cylinder of uniform mass density of 2,400kg/m^3 with length L=60m with R1 of 2.8m. Find its outer radius (R2) in m if the moment of inertia is 5, 067, 000kgm^-2 about its axis to symmetry is.
Find the equivalent moment of inertia of the rocker arm assembly with respect to the location of kt. mass1=10kg Jo=20kg-m2 mass2=15kg, a is half of b. The rocker is 30 centimeters long. (kg-m2)
b) Find the moment of inertia tensor of a solid hemisphere of mass M and radius R centered at the origin, where the base of the hemisphere is placed on the z = 0 plane and is facing towards the -z- axis and. x Z (0,0,0) ***** *********** R L ********************* y
An oversized yo-yo is made from two identical solid disks each of mass M - 1.60 kg and radius R- 9.0 cm. The two disks are joined by a solid cylinder of radius r- 4.00 cm and mass m - 1.00 kg as in the figure below. Take the center of the cylinder as the axis of the system. (a) What is the moment of inertia of the system? Give a symbolic answer. (Use any variable or symbol stated above as necessary.) moment of inertia- MR + (b) What torque does gravity exert on the system with respect to the given axis? V N-m Take downward as the negative coordinate direction. (c) As depicted in the figure above, is the torque exerted by the tension positive or negative? (View the yo-yo from the left and let the countercdockwise direction be positive.) positive O negative (d) Is the angular acceleration positive or negative? O positive O negative (e) What about the translational acceleration? O positive O negative () Write an equation for the angular acceleration a (alpha) in terms of the translational…
The assembly in figure 1 is rotating counterclockwise from above at w = 10 rad/s about the z axis. The thin disk has mass 12 kg and radius 15 cm, while, and the thin rod CD has mass 3 kg and length 30 cm. axis. @=10 rad/s B C A 15 cm Figure 1 30 cm Find the inertia tensor for the disk and rod CD about the axis CD. Calculate the moment of inertia of the disk and rod CD about the vertical z Determine the angular momentum of the disk and rod CD about the z axis.