RI Ci a VSm ISm ZVSph L1 ZISph b In the circuit, the voltage source amplitude and phase are 40 V and 0.75 rad correspondingly; the current source amplitude and phase are 20 mA and 0.75 rad correspondingly; The signal frequency of both sources is 26 MHz; R1=8 kohm, L1= 45 uH (u=micro), C1= 1.4 pF. Using any appropriate techniques, find the following parameters of Thevenin equivalent circuit with respect to the terminals "a" and "b". Present the Thevenin source in the polar form and the Thevenin impedance in the algebraic form.

RI Ci a VSm ISm ZVSph L1 ZISph b In the circuit, the voltage source amplitude and phase are 40 V and 0.75 rad correspondingly; the current source amplitude and phase are 20 mA and 0.75 rad correspondingly; The signal frequency of both sources is 26 MHz; R1=8 kohm, L1= 45 uH (u=micro), C1= 1.4 pF. Using any appropriate techniques, find the following parameters of Thevenin equivalent circuit with respect to the terminals "a" and "b". Present the Thevenin source in the polar form and the Thevenin impedance in the algebraic form.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Using a positive Clamper Circuit, with an AC voltage of Vi = 100v with a frequency of 30hz, a value of 1000u for the Capacitor, a silicon diode and a resistor with the value of 100 ohms. Find the voltage value on the resistor at a simulation of Oms. Vm 2Vm Mr. Vm Vo -Vm Input Waveform Output Waveform Positive Clamper circuit
D1 D V1 D4 D2 V D D Diode Model: 1N5817 R = 10k Vi= sine (0 5 100) Given the parameters above, simulate the given circuit using .tran 0 30m 0. Solve for the output peak to peak voltage across the resistor and the output frequency measured across the resistor. Output Frequency = (When computing for the frequency, use 4v as reference point) Output Voltage (pk-pk) = + R1 R D3 D
A bridge full - wave rectifier with a capacitor - input filter provides a dc output voltage of 14.5 V to a 330 ohm load. Determine the value of filter capacitor if it connected to input voltage of 12 V rms, 50 Hz. Question 7Answer a. 220 ɲf b. 208 ɲfc. 440 fd. 104 nf
The circuit is shown below, Vin is the sinusoidal waveform with magnitude 5V and frequency is 100 Hz, R = 1 k, C = 1 uE, the chip is supplied by + 12 V source. a) What is the waveform of Yout? b) Calculate the magnitude of Vo c) If Vin is triangle waveform, what is the output waveform? -Vout , if Vin is triangle waveform with magnitude of 5 V (peak-to-peak value is 10 V) and frequency is 10 kHz, calculate waveform of you and the magnitude of I/?
Draw the small signal equivalent circuit of the following circuit. Note that C1 and C2 are large AC coupling capacitors. 5 VIO C1 RF Q1 C2 fem RL Vo
I want to design an oscillator for a PWM supply. It will run with a square wave of 75 KHz. Voltage is 15VDuty Cycle about 50%. Hint: Choose values of resistor, and then calculate capacitor for the frequency. Draw the circuit. Show the calculations.
Q2. For the circuit shown below, sketch i, & Vo 60 a. Find the conduction angle of the thyristor. b. Find the average output voltage V. R-6.50 f- Go Hz = 27AL = 120x17X10 = 6.4092 075 LO = RrjX= Vo L-17mH 6.5+j6.469=9.128 (44595 075 75V( Es 24 Vm A e
What voltage is boosted at the output of a multiplier.Choices: average, rms, peak, or instantaneous Which assumption is not used in the analysis of multipliers?Choices: a capacitor will not discharge, start with the cycle of the source that will forward bias the nearest diode, the output will always be multiplied, or a single diode is forward biased at a time A voltage multiplierChoices: multiplies the output voltage, has very high voltage and low current ,can employ inductors, or may not have equal numbers of diodes and capacitors A voltage regulator maintains constant voltage at the load regardless of variations atChoices: the input and output, the load, source, or in the environment Between a lower percent regulation and a higher one, which is better?Choices: lower or higher
this is electric circuit questin ...plz solve it early .plz solve early
Q-4. When VGs of a JFET changes from -3.1 V to -3 V, the drain current changes from 1 mA to 1.3 mA. Then the value of trans-conductance is .
Determine the waveform, theoretical, of the peak output voltage at Resistor L. 120 V rms 5:1 ooooo elele D₁ D3 D21 DA 4 R₁ WWW II Vout
3. Determine Veand Sketch output waveform for the clamper network shown. 20 V Si C Vi R 4 V- | -20 V 4. An RC filter stage (R = 42 0, C = 220 µF) is used to filter a signal of 30 V dc with 6 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 200-mA load. Also calculate the ripple of the filtered signal applied to the RC stage.