The rigid bar ABC supports a load of 21.1 kN at point C. A circular rod (diameter 25 mm) supports the bar at B. The length ofAB is 3.5 m and the length of BC is 1.1 m. Calculate the normal stress in the rod. Provide your answer to 2 decimal places inMPа.Roddiameter= 25mmВyF kN

Answered: The rigid bar ABC supports a load of…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 1: Given that Tuitow = 50 MPa for the rod AB and tattow = 25 MPa for the rod BC. If T=1250 N.m, find the required radius for both rods. Ahmtmum AB = BC =
The rigid bar BC is supported by the steel rod AC of cross-sectional area 0.31 in2. Find the vertical displacement (in inches and absolute value) of point Coaused by the 2888-lb load if x = 8.7 ft and 8 = 46.5-. Use E = 29159 ksi for steel. Note: Round off the final answer to four decimal places. Rigid B P
The homogenous bar that weighs 5000 Ib is supported by a pin at Cand a cable that runs from A to B around the frictionless pulley at D. If the diameter of the cable is 0.8 inch, calculate its axial stress. Express your answer in ksi (kips per sq. inches) with one decimal place only (Note: Give only the numerical value of the answer. DO NOT INCLUDE THE UNIT IN THE ANSWER) * D F 3 ft 5 ft 5 ft
The rigid bar AB shown below is supported by a steel rod AC having a diameter of 20 mm, and a block. Ignore the weight of AB and AC, and the distributed load on AB is p = 4.0 KN/m. Determine the axial normal stress developed in AC: = ____ MPa. Calculate your answer to 1 decimal place.
The force P is applied on the top of the solid cylindrical body which rests on a circular cap as shown below. Determine the smallest dimensions di, ds, and t required to support the load P. Use the table given below and your student ID to obtain the values of the force P and the allowable stresses for all the materials used in the problem (ie., Pand the allowable stresses are given). 30 mm allowable allowable tensile stress (kPa) allowable shear stress (kPa) Student bearing P(N) ID stress (kPa) 1000 175 300 155
Q1 :In the following arrangement of structure (fig1) each sold bar has a 36N/m weigh .If the allowable shear stress in pin C is 16 Mpa calculate the pin diameter at A. If the diameter of bar is (10 mm) what is the bearing stress on bar AB. Fig 1 B 36N/M 2m 1m pin apport Im 2m WINDE
Q1 :In the following arrangement of structure (fig1) each sold bar has a 36N/m weigh .if the allowable shear stress in pin C is 16 Mpa calculate the pin diameter at A. If the diameter of bar is (10 mm) what is the bearing stress on bar AB. Fig 1 36N M 2m 1m Im 2m
QUESTION 4 Figure 3 below shows a vertical rod under its own weight. Find the displacement at A and stress distribution. Use E-100 MPa and weight per unit volume 0.06 N/cm³. Solve using two elements and comment on the stress distribution. 1.6 m 1m A Area = 2500 cm² 8 B Area = 1500 cm²
Q1 :In the following arrangement of structure (fig1) each sold bar has a 36N/m weigh If the allowable shear stress in pin C is 16 Mpa calculate the pin diameter at A. If the diameter of bar is (10 mm) what is the bearing stress on bar AB. Fig 1 B 36N/M 2m 36N/M 1m pia veppt 2m Im
For the stresses given with the cube below: 1. Compute the center, radius (R), principal normal stresses (0₁ and 03), max shear stress (Tmax) and draw the Mohr's Circle. 2. Compute the normal and shear stresses when the cube is rotated 20° clockwise from the horizontal plane and draw them on the cube. 3. The yield point stress (σyp) is 6 kPa. Determine if the material will fail under stresses shown using Tresca's Hexagon. вкра акра 6 экра 8 кра экра 4кра
A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load of 500 MN. If the maximum allowable stress for this hollow rod is 325 kN/mm?, calculate the minimum thickness of the rod. Give your answer in millimetres (mm) and to 2 decimal places.
Find the tension of the cord that extends from point C to D and compute for stress experienced by the cable if it's diameter in 1.51 in2. Neglect the members weight and friction. Round-off your answer into the nearest whole number. 150 Ib/ft 6 ft ft 6 ft 12 ft ft ANS: T = Ib, Stress = ksi

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

The rigid bar ABC supports a load of 21.1 kN at point C. A circular rod (diameter 25 mm) supports the bar at B. The length of AB is 3.5 m and the length of BC is 1.1 m. Calculate the normal stress in the rod. Provide your answer to 2 decimal places in MPа. Rod diameter = 25mm