Interpretation:
The molar concentration of
Concept introduction:
Calibration of instrumental methods: The purpose of calibration which is required by all types of analytical methods is quantitation. It is defined as a process in which the measured analytical signal and the concentration of analyte are related to each other. The three most common methods to calibrate are:
- Calibration curve.
- Standard addition method.
- Internal standard method.
In case of standard addition method, standards are added to the aliquots of sample, keeping the matrix components same. On each solution, instrumental measurements are made to obtain instrument response ( S ).
The relation between the instrument response and concentration if they are proportional is,
Where,
Trending nowThis is a popular solution!
- A 10.00-g sample containing an analyte was transferred to a 250-mL volumetric flask and diluted to volume. When a 10.00-mL aliquot of the resulting solution was diluted to 25.00 mL it was found to give a signal of o.235 (arbitrary units). A second 10.00-mL aliquot was spiked with 10.00 mL of a 1.00- ppm standard solution of the analyte and diluted to 25.0o mL. The signal for the spiked sample was found to be o.502. Calculate the weight percent of analyte in the original sample.arrow_forwardThe student was supposed to measure the pH of a 0.1 M hydrochloric acid solution. For this purpose, he used a pH-meter and obtained the following results: 0.90, 0.93, 1.04, 1.02. Present the appropriate graphic and statistical elaboration of the performed analysis and confirm whether the applied pH-meter worked properly.arrow_forwardWhat are the differences between systematic and random errors and how do they effect accuracy and precision? In what circumstances would you use standard addition (versus a normal calibration curve) to determine the amount of an analyte in a sample? A urine sample, containing analyte Z is analysed by the standard addition method where 5 mL of the original sample was mixed with increasing amounts of a Z standard and each solution diluted to a volume of 50 mL prior to analysis. A plot of the final concentration of the standard in each of the 50 mL samples (x axis) versus The measured signal from the analysis of each 50 mL sample (on y axis) produced a straight line with the general equation: y = 44.72x + 4.06 what was the final concentration of Z in the 50 mL standard addition sample? what was the initial concentration of Z in the original urine sample?arrow_forward
- A spectrophotometric method for the quantitative analysis of Pb2+ in blood has a normal calibration curve for which Sstd=(0.296 ppb−1)×Cstd+0.003. What is the concentration of Pb2+ in a sample of blood if Ssamp is 0.397?arrow_forwardBlue Blue dye stock solution 0.293 M Absorbance at 630 nm 0.00265 Calibration curve y = 0.0833x A solution is prepared by diluting 2.81 mL of the blue dye stock solution to 25.00 mL. The measure absorbance for the prepared solution is listed in the data table. (a) What is the theoretical molar concentration? [Blue]theoretical | × 10 |M (b) What is the experimental molar concentration? [Bluelexperimental x 10 M (c) What is the percent error? Percent error (blue) =arrow_forward7) A 25.0 ml sample containing Cu gave an instrument reading of 23.6 units (corrected for a blank). When exactly 0.500 ml of 0.0287M Cu(NO3)2 Was added to the solution,the signal increased to 37.9 units. Calculate the molar concentration of Cu" in the sample +2,arrow_forward
- The standard curve was made by spectrophotographic analysis of equilibrated iron(III) thiocyanate solutions of known concentration. You are asked to analyze a Fe(SCN)2+ solution with an unknown concentration and an absorbance value of 0.392. The slope-intercept form of the equation of the line is y = 4538.1x +0.0077. The unknown was analyzed on the same instrument as the standard curve solutions at the same temperature. What is the Fe³+ concentration of the unknown solution? [Fe³+] = mol/L Absorbance Iron(III) thiocynate standard curve 1.0 V 0.5 0.0001 Fe³+ concentration (M) 0 0.0002arrow_forward(Standard addition) Tooth enamel consists mainly of the mineral calcium hydroxyapatite, Ca10(PO4)6(OH)2. Trace elements in teeth of archeological specimen provide anthropologists with clues about diet and diseases of ancient people. Student at Dankook University measured the trace element strontium (Sr) in enamel from extracted wisdom teeth by atomic absorption spectroscopy. Solutions were prepared with a constant total volume of 10 mL containing 0.750 mg dissolved tooth enamel plus variable concentrations of added standard Sr. Added Standard Sr (ng/mL=ppb) 0 2.50 5.00 7.50 10.00 Emission Signal 28.0 34.3 42.8 51.5 58.6 (a) Make a graph showing the experimental data and the calculated straight line. (b) Find the concentration of Sr in the tooth ennamel in parts per million = μg/mL.arrow_forward(a) For use in an iodine titration, you prepare a solution from 0.222 2 (+0.000 2) g of KIO3 [FM 214.001 0 (+0.000 9)] in 50.00 (+0.05) mL. Find the molarity and its uncertainty with an appropriate number of significant figures. (b) Would your answer be affected significantly if the reagent were only 99.9% pure?arrow_forward
- A 10.00 mL of natural water sample containing Ni2+ was pipetted into a volumetric flask and diluted to 50.00 mL with pure water. In the second 10.00 mL of natural water sample transferred into a volumetric flask, exactly 4.00 mL of a Ni2+ solution with a concentration of 5.99 mg/L was added and then diluted to 50.00 mL with pure water. The measured absorbance is A1= 0.436 and A2 = 0.663. What is the Ni2+ concentration in unit of mg/L in the natural water sample?arrow_forwardDifferentiate between qualitative analysis and quantitive analysis?arrow_forwardTreatment of ammonia with phenol in the presence of hypochlorite yields indophenol, a blue product that absrobs light at 625 nm, which çan be used for the spectrophotometric determination of ammonia. gan OCF OH + NH3 indophenol anion To determinè the ammonia concentration in a sample of lake water, three samples are prepared. In sample A, 10.0 mL of lake water is mixed with 5 mL of phenol solution and 2 mL of sodium hypochlorite solution, and diluted to 25.0 mL in a volumetric flask. In sample B, 10.0 mL of lake water is mixed with 5 mL of phenol solution, 2 mL of sodium hypochlorite solution, and 2.50 mL of a 5.50 x 10-4 M ammonia solution, and diluted to 25.0 mL. Sample C is a reagent blank. It contains 10.0 mL of distilled water, 5 mL of phenol solution, and 2 mL of sodium hypochlorite solution, diluted to 25.0 mL. The absorbance of the three samples is then measured at 625 nm in a 1.00 cm cuvette. The results are shown in the table. Sample Absorbance (625 nm) A 0.361 B 0.608 C…arrow_forward
- ChemistryChemistryISBN:9781305957404Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCostePublisher:Cengage LearningChemistryChemistryISBN:9781259911156Author:Raymond Chang Dr., Jason Overby ProfessorPublisher:McGraw-Hill EducationPrinciples of Instrumental AnalysisChemistryISBN:9781305577213Author:Douglas A. Skoog, F. James Holler, Stanley R. CrouchPublisher:Cengage Learning
- Organic ChemistryChemistryISBN:9780078021558Author:Janice Gorzynski Smith Dr.Publisher:McGraw-Hill EducationChemistry: Principles and ReactionsChemistryISBN:9781305079373Author:William L. Masterton, Cecile N. HurleyPublisher:Cengage LearningElementary Principles of Chemical Processes, Bind...ChemistryISBN:9781118431221Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. BullardPublisher:WILEY