Refrigeration and Air Conditioning Technology (MindTap Course List)
8th Edition
ISBN: 9781305578296
Author: John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 16, Problem 7RQ
When a large volume of air is needed at a diaphragm, the thermostat may feed branch line pressure to the_______.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Why is a low-voltage thermostat normally more accuratethan a high-voltage thermostat?
What is the primary purpose of a thermostat
jiggle valve?
Select one:
a. To act as a bypass for coolant
b. To relieve water pump pressure
under load
c. To ensure coolant flows the correct
direction
d. To aid in bleeding air from the
system
to run
d. both a and b
44. Ifa thermostatic expansion valve's thermal bulb came loose from the suction line at the outlet of the
evaporator, whích of the following could result?
The bulb pressure would increase and the c.
thermostatic expansion valve would
open.
b. The superheat in the evaporator would
decrease.
a.
Liquid refrigerant would flow back to the
compressor.
d.
All of the above are correct.
45. If the thermal bulb assembly develops a leak, what will occur?
All of the system's refrigerant will leak
a.
The valve will open to allow more
c.
refrigerant to flow.
d. It will have no effect on system
operation.
out.
b. The bulb pressure will reduce and the
valve will close.
46. The purpose of an externally equalized thermostatic expansion valve is to
compensate for excessive evaporator
pressure drop
b. allow system to equalize faster
a.
prevent the expansion valve from
frosting up
d.
c.
allow refrigerant to expand in the
compressor
47. The primary function of an expansion device is…
Chapter 16 Solutions
Refrigeration and Air Conditioning Technology (MindTap Course List)
Ch. 16 - True or False: Pneumatic controls are...Ch. 16 - Pneumatic controls are operated by A. water. B....Ch. 16 - One advantage of a modern control system is A....Ch. 16 - A control loop contains _______, _______, and...Ch. 16 - Pneumatic air must A. be clean and dry. B. have...Ch. 16 - The air supplied to a diaphragm is 20 psig, and...Ch. 16 - When a large volume of air is needed at a...Ch. 16 - Prob. 8RQCh. 16 - Prob. 9RQCh. 16 - An analog control signal A. has an infinite number...
Ch. 16 - Another term used to describe sensitivity in...Ch. 16 - Prob. 12RQCh. 16 - Prob. 13RQCh. 16 - One of the major components of a residential...Ch. 16 - Prob. 15RQCh. 16 - Describe a control device, and give three examples...Ch. 16 - Describe what a sensor does in a DDC system used...Ch. 16 - What is the difference between an active and a...Ch. 16 - A control system consists of what three basic...Ch. 16 - List six advantages that DDC control systems have...Ch. 16 - Describe the difference between the analog and...Ch. 16 - Describe the difference between an open-loop and a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- If the thermostat contacts are closed the compressor and the condenser fan motor are not operating, and all the other loads are operating properly, which might be the problem? A. A bad high pressure safety switch. B. A bad low pressure switch C. Both A. and B. D. A bad thermostatarrow_forwardWhat type of control would be used to turn a compressor off in the event of a large refrigerant leakarrow_forwardWhat does a cold anticipator do?arrow_forward
- Why are digital scales preferred over other types for charging refrigeration and air-conditioning systems?arrow_forwardQuestion1. If an air conditioning system has three independent zones, how many space thermostats will the system have? Question 2. A technician is traversing a duct and obtains the following 8 velocity: 500fpm, 400fpm, 375fpm,625fpm,275fpm,360fpm,450fpm,and 575fpm. What is the velocity value that can be used for the system calculations?arrow_forwardWhen using a time-cycled/ pressure-limited ventilator, what will happen when the preset time limit is reached?arrow_forward
- What two types of switches are normally found in the subbase of a low-voltage thermostat?arrow_forwardWhich of the following statements is false? The condenser is normally mounted just in front of the radiator. The receiver/dryer is a storage tank for the liquid refrigerant from the condenser. An accumulator is not used in any system with a receiver/dryer. All of the above.arrow_forwardThe cooling anticipator is wiredA. in parallel with the cooling contact.B. next to the liquid line.C. in series with the cooling contact.D. inside the indoor unit.arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Hydronics Step by Step; Author: Taco Comfort Solutions;https://www.youtube.com/watch?v=-XGNl9kppR8;License: Standard Youtube License