Applied Statics and Strength of Materials (6th Edition)
6th Edition
ISBN: 9780133840544
Author: George F. Limbrunner, Craig D'Allaird, Leonard Spiegel
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 9, Problem 9.25CP
Write a computer program that will calculate the allowable load for a single-shear bolted lap connection similar to that shown in Figure 9.12. 
The computed allowable load is to be based on bolt shear only. User input is to be number of bolts, bolt diameter, and allowable shear stress for the bolts.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A 3/8-18 grade 8 bolt has 800 pounds of force
pulling on it. Find the tensile force, the thread
stripping strength for the needed length of
engagement and the factor of safety for the bolt
with that amount of force.
2.
Calculate the shear stress in a simple pin joint, assuming pin diameter of 10 mm and
3550N compressive load on the link.
Draw a free body diagram (geometry & forces)
Identify stress plane
Calculate stress and write it (with appropriate units) in the outlined box
Condition #1:
A structural support for a machine is subjected to a static compression load of 20 kN. The support is
manufactured from a circular rod made from SAE 1040 Hot Rolled steel. Specify suitable diameter for
the cross section of the rod based on the basic size. Steel data are available in Table A-10 from the
textbook.
Condition #2:
The same structural support of the basic size determined in Condition 1 is subjected to a tensile load of
15 kN that is repeated several thousand times over the life of the machine. This load is not an addition to
the 20 kN. Specify a suitable steel that is suitable to this application based on the basic size determined in
Condition #1. Loading of Condition #1 does not apply here.
Condition #3:
The same structural support from Condition 2 is heated from room temperature of 25°C. The support is
placed inside a frame on both ends. There is a total clearance of 0.2 mm between the support and its
frame. Initial length of the rod is 200 mm. Specify the…
Chapter 9 Solutions
Applied Statics and Strength of Materials (6th Edition)
Ch. 9 - Write the direct stress formula in its three forms...Ch. 9 - A 6-in-diameter concrete test cylinder is loaded...Ch. 9 - Determine the tensile stress in each segment of...Ch. 9 - Calculate the stress developed in the following...Ch. 9 - The following members are subjected to axial...Ch. 9 - Determine the stresses in the two segments of the...Ch. 9 - A bin weighing 8 tons is supported by three steel...Ch. 9 - Diameters of small commercially available steel...Ch. 9 - A No. 32 (metric designation) reinforcing bar for...Ch. 9 - In the bolted connection of Figure 9.12 , assume...
Ch. 9 - Compute the force required to punch a...Ch. 9 - The 34 — in. — diameter bolt shown is subjected to...Ch. 9 - Why is strain unitless (or dimensionless)?Ch. 9 - (a) Given =1.2in. and L=100ft calculate (b) Given...Ch. 9 - A short compression member 2 in. by 2 in. in cross...Ch. 9 - A 100-ft-long rod is suspended from one end. The...Ch. 9 - Compute the total elongation of a steel bar,...Ch. 9 - A steel rod 34 in. in diameter and 25 ft long is...Ch. 9 - An aluminum rod 25mm in diameter and 4m long is...Ch. 9 - A steel rod 10 ft long is made up of two 5 ft...Ch. 9 - A titanium alloy bar elongates 0.500 in. when...Ch. 9 - Write a program that will calculate the allowable...Ch. 9 - Write a program that will compute stress, strain,...Ch. 9 - The Viking Bin Company manufactures suspended bins...Ch. 9 - Write a computer program that will calculate the...Ch. 9 - The joint between a diagonal and a chord in a...Ch. 9 - In Problem 9.26, find the required length of the...Ch. 9 - A column is supported by a base plate, pedestal,...Ch. 9 - If the soil pressure under the footing of Problem...Ch. 9 - A hopper weighing 75 kN is supported by three...Ch. 9 - A steel bar has a rectangular cross section 25 mm...Ch. 9 - A steel wire is suspended vertically from its...Ch. 9 - A W1240 shape is subjected to a tensile load of...Ch. 9 - Calculate the required diameter of steel tie rods...Ch. 9 - A 30-ft-long steel rod of circular cross section...Ch. 9 - Consider the bolted lap joint shown in Figure...Ch. 9 - An inclined member is braced with a glued block,...Ch. 9 - Calculate the force a punch press must exert if it...Ch. 9 - A 34 - in. - diameter punch is used to punch a...Ch. 9 - A control arm is keyed to a 1-in. -diameter shaft...Ch. 9 - Calculate the required width b for the key of...Ch. 9 - A 25-mm-diameter aluminum rod, 3 m long, is...Ch. 9 - A short timber post of Douglas fir is subjected to...Ch. 9 - A 1 00-ft surveyor’s steel tape with a...Ch. 9 - An 18-in-long steel rod is subjected to a tensile...Ch. 9 - Compute the magnitude of the tensile load that...Ch. 9 - A 5-mm-diameter steel wire, 18 m in length, is...Ch. 9 - A structural steel rod 112 in. in diameter and 20...Ch. 9 - A rectangular structural steel eyebar 34 in. thick...Ch. 9 - 9.50 A
in. — diameter steel rod, 100 ft long, is...Ch. 9 - For the truss shown, compute the total deformation...Ch. 9 - A steel bar with a cross section of 12 in. by 12...Ch. 9 - Rework Problem 9.52 , changing the second load...Ch. 9 - In the structure shown, the tie-back BC is a round...Ch. 9 - A hook is suspended by two steel wires, as shown....Ch. 9 - The trolley of a small hoist is supported on a...Ch. 9 - The steel piston rod to the master cylinder has a...Ch. 9 - A stranded steel brake cable is composed of 7...Ch. 9 - The piston of a steam engine is 400 mm in diameter...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The two lever assembly shown below is subject to a static load F = 8250 lb. %3D (a) identical links BD can be made from based on the stress in the middle of each link. Specify the lowest-strength alloy steel from Appendix A-10 that the two (b) is the minimum recommended diameter that the pins can be machined to? The pins at B and D are made from SAE 4140 OQT 900 alloy steel. What What is the bearing stress on the pins at B and D based on the pin (c) diameter you calculated in part (b) above? 9 in 8 in C B Top View A В C B 0.75 in - -0.31 in F 0.31 in Side View Front Viewarrow_forwardCondition #1: Å structural support for a machine is subjected to a static compression load of 20 kN. The support is manufactured from a circular rod made from SAE 1040 Hot Rolled steel. Specify suitable diameter for the cross section of the rod based on the basic size. Steel data are available in Table A-10 from the textbook.arrow_forwardHi, I have been given this pin-jointed frame analysis to solve (see pictures of the structure attached). Can you help me answer all the questions below? Especially the one about the bending moment and shear force. The Figure 2 attached is a simplified structure to undertake a structural analysis on a concept design for a low cost stroller/buggy for children. The buggy consists of a number of metal sections that are pin-jointed together. The buggy is designed to accommodate a child of mass no more than 20 kg, sat on the seat which is supported at four points (Fc) on the frame of the buggy. Assume that the weight of the child is equally distributed across all of the points indicated on Figure 2 as Fc. Assume that there are no additional forces applied to the handle of the buggy, that the buggy is static (stationary) and that the buggy, and the elements of the frame have no mass. At points A and G, there are roll supports. At Points B, F and D there are the pin supports. I am required…arrow_forward
- The butt connection shows 8- 22 mm diameter bolts(bolt hole dimension of 26 mm) spaced as shown below. Steel strengths are Fy 248 MPa and F, = 400 MPa. Use NSCP 2010/2015 Code Provisions %3D Calculate the design tensile strength based on the following: Based on the gross area of the plate Based on the net area of the plate. Based on block shear strength. CS Scanned with CamScannerarrow_forwardHi please help me answer this problem and draw free body diagramarrow_forward3. An M16 x 2 bolt with a slotted hex nut is used to clamp together two 25 mm steel plates. The joint is assembled with a size 16 N washer underneath the bolt head. The bolt is a 5.8 class metric grade, with a proof strength of 380 MPa. The joint is intended to be permanent. Determine a suitable length for the bolt, rounded up to the nearest standard size in millimeters. Calculate the bolt stiffness, the elongation of the bolt after the necessary preload is developed, and the bolt torque required to apply the preload. Assume that coefficients of friction between the bolt, nut, and collar are all ~0.15. For steel, use E = 207 GPa. Standard threaded fastener lengths, dimensions of hexagonal nuts, and dimensions of metric plain washers are provided in the textbook appendices.arrow_forward
- The forces shown in the following figure act on a specific screwed part. It can be noted that none of them acts directly on the known x and y axes. With this, what should be the force component acting on these axes? Options: a) The force on the x-axis is 20.54 N; and on the y-axis, it is 250.22 N. B) The force on the x-axis is -20.54 N; and on the y-axis, it is 230.22 N. c) The force on the x-axis is -22.54 N; and on the y-axis, it is 190.98 N. d) The force on the x-axis is 21.20 N; and on the y-axis, it is -234.89 N. e) The force on the x-axis is -20.54 N; and on the y-axis, it is 250.22 N.arrow_forwardProblem is easy just start calculation from point C Hit identify zero force and solve What is the force in brace #1 (tension positive)? What is the force in brace #2 (tension positive)? What is the force in brace #4 (tension positive)? What is the force in brace #5 (tension positive)?arrow_forwardA structural support for a machine is subjected to a static compression load of 20 kN. The support is manufactured from a circular rod made from SAE 1040 Hot Rolled steel. Specify suitable diameter for the cross section of the rod based on the basic size. Steel data are available in Table A-10 from the textbook.arrow_forward
- Please answer in this format. Sketch: Given: Required: Solution: (Please answer in detailed (step by step). Indicate labels on what you are doing/performing, for example what formula is used) A torque To is transmitted between two flanged shafts by means of four 20-mm bolts. diameter of the bolt circle is 2=150mm. If the allowable shear stress in the bolts is 90 Mpa, what is the maximum permissible torque? Disregard friction between between flanges. The Toarrow_forward-.3: Draw the front view for a square-headed bolt and a square neck with a castle nut and a washer in position. Take the bolt diameter is 24mm and length is 100mm.(use ISO metric threads) Your answer •ns: Draw the two views (front and top) of a two plates (thickness 5 mm) joined by a single riveted , double strap butt joint. use a Round top countersunk head for the rivet( see Figure). The curve of the head R=1.0606*d 1.5 d 0.2 d 0.25 darrow_forwardSketch a V-grooved butt joint, and label all of the joint's dimensions.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Differences between Temporary Joining and Permanent Joining.; Author: Academic Gain Tutorials;https://www.youtube.com/watch?v=PTr8QZhgXyg;License: Standard Youtube License